. Rashist ???

  . Rascal ( epsi's, incl CNC )               Inleiding ?    Data ?

  . Yras, Ypitch , incl Slof?? )              Inleiding ?    Data OK

  . Zras, Ypitch , incl Slof??, BOLmon ?? )       "          Data OK

  . DYmulti ( Incl TowersSlof?? en CNC)                    data OK

  . Xtomo                                     Inleiding ?   vgl Rasnik OK

  . GL                                        Inleiding ?    Data OK

  . Lijm ( incl. Forces??, Temp?? )           Inleiding ?    Data OK

  . Multidik

  . Buis

 -------------------------------

  . Mallen ( incl CNC, Slof, BOLmon , Si )

  . Towers       "       "


=========now============now============now============now============now============now============now=== 

jigs.text   beschrijving Frascati+NIKHEF jigs         Figures
                   productie
                   CNC meet-resultaten
                   Montage op Graniet
                   BOL-monitor                        [xyxbol11.ps] 
                   Si-sensor                          [sisens]?
                   (Slof)

guido.text        Control of the tube position,
                  Guido Laser                          [guido.AB]\  Marcel
                                                       [guido.CD]/

layer.text        Layer-pitch control
                  RasAss,Inplane,XP
                  Calibration
                  Layer Z-pitch                        [zsahv],[ztomras]
                  Layer Y-pitch                        [yshav.ps],[mooi.ps]
                                                       [tomrasy.ps]
                  Middle XP                            [hismid.ps]


=========now============now============now============now============now============now============now=== 

               in jigs.text
                  =========
The 'Frascati' Jigs :  OK behalve TempCNC? -> pitch at 20deg ?
------------------
            [ref.Frascati.jigs]

            geen plaatjes

The Tube Jigs  : OK , geen plaatjes
-------------

Jigs on the Assembly table : OK  
--------------------------

            .  DY ref/nonref -> wig en DZmulti ?


             [Assembly.intro]

        BOL-monitor   fig [xyzbol11.ps]   parallel XP N/S ?
        ..........

        foil FrascJigs 10/20mu ?

        Parallel Frascatie xxx murad ? , distance yyyy mm ?

        SiSens    [ref SiSens/Munich]
        ......
                  strip-pitch SiSens 100 mu?

                 some of the measurements. The rms of the deviations is typically
                  xx \mu in z and yy \mu in y, thus amply fulfilling the requirement


                  [ plaatje ?]

         Sliding jig fixation
         ...........

         SLOF meas, Frascati
         ...................


               in guido.text
                  =========

   Control of the tube position
   ----------------------------

                   [Assembly.jig]

                   ( see Assembly.QA.Guido ). 

                   fig [guido.AB]
                   fig [guido.CD]

                   X-ray tomograph scans for BOLx??.
                   ( nu ook BOL7/8?)


               in layer.text
                  =========

   Layer-pitch control
  -------------------

              [ see Assembly.SagComp]

  Layer Z-pitch
  -------------
 
      In fig[zshav.ps] we plot for chambers BOL0 to BOL8 
      
     (see also fig [mooi.ps] ).

     In contrast the z-values at the non-reference side fluctuate
     by typically +-5?\mum as a consequence of small temperature ( +-0.1? deg)
      the z-positions at the two sides are found to be consistent within ?? \um.

     In fig[ztomras.ps] 

      see [Assembly.LandingGear]

  Layer Y-pitch
  -------------

  In fig[yshav.ps] we plot for chambers BOL0 to BOL8 

 We attribute this to the shrinkage of the particular glue [XXX]<-
 that is used to glue the innermost layers to the spacer. 
 For this glue we observed in a simple test 
 a shrinkage of the order of a few permille??.<-

 are shown in fig [mooi.ps] for the glueing of the first 4 layers

  during curing of the [YYY] glue used for these layers. In this

  In fig[tomrasy.ps] we compare the Y-pitch deviations  

  Relative positioning at the middle cross-plate
  ----------------------------------------------           
     In fig[hismid.ps] we plot the deviations from the nominal layer pitch

  of the tubes, as the mechanical precision of the middle stacking blocks
  is also of order 10\mum ( see [AssJig.par] ).

 as presented in table  [Tomo.sitepar]


-----------------------------------------------------------------------
                                crossref-summary 

references-external :
            [ref SiSens/Munich]
            [ref.Frascati.jigs]

references-internal :

            [Assembly.intro]
            [Assembly.jig]
            [Assembly.QA.Guido]
            [ see Assembly.SagComp]
            [Assembly.LandingGear]
            [AssJig.par]


plots :
          [xyzbol11.ps]
          [guido.AB]     == gl1.ps and gl2.ps\ nu nog PWPNT plaatje T_dec01
          [guido.CD]        Martin/Marcel ?  /
          [zshav.ps]
          (see also fig [mooi.ps] ).
          [ztomras.ps] 
          [yshav.ps]
          [mooi.ps]
          [tomrasy.ps]
          [hismid.ps]

tables :

        [Tomo.sitepar]



------------------------------------------------------------------------

Missing :        QA/QC text/data/plaatjes :

                               .  Multidik ?
                               .  Indelucht en InplMaskAngles ?

                               . Buisdata 
                                    Tubbies Leak/HV
                                   ( wpos,tension,length )

                               . Tomo

                  Inleiding
                          . Algemeen
                          . Tubes  + Wiring
                          . Assembly Jigging,Procedures
                            (Spacer/Rasniks/Temp)
                          . BOLroom
                          . Gluemachine

                  Uitleiding
                          . production time
                          . cosmics